Epoxy Vs Resin, The Difference Explained | Epoxy Countertop DIY

Epoxy Vs Resin, The Difference Explained

Choosing the wrong resin for your project could result in a ruined project. Some resins require thin pours while others require long cure times. Pour a thin pour coating epoxy too thick and it will result in an accelerated reaction which could crack, yellow or fish eye the epoxy. Some epoxies utilize convoluted mixing ratios and catalyst while others are a simple 1 to 1 mixtures. Casting Resin, Epoxy Coating, Polyester Resin, and the list goes on; but what's the difference between each?

The Difference Between Epoxy And Resin

To make matters more confusing, differentiating between epoxy and resin is not the proper terminology. Epoxy Resin is its' own type of compound and so too is Casting Resin. However, when comparing the difference between the two, most are comparing a Casting Resin, Polyester Resin and an Epoxy Coating Resin. Polyester Resins are mostly used in the marine industry, so for the sake of this DIY Epoxy site and this comparison we will focus on the difference between Casting & Coating Resins

Epoxy Coating Resins Vs Casting Resin

The most obvious difference between the two is the intended use. Epoxy resins are meant for coating applications whereas casting resins are meant for casting applications such as molds, figurines, & jewelry. However, that is not to say that either would not work for their opposite intended uses, but more on that later.

Casting Resin

  • Thinner Viscosity
  • Slower Cure Times
  • Longer Working Times
  • Thicker Max Pour Depth
  • Varied Mix Ratios

Epoxy Resin

  • Thicker Viscosity
  • Quick Cure Times
  • SHORT Working Times
  • Requires Thin Pours
  • Easy Mix Ratios

-Viscosity- The Thickness Of The Material

Build Dam Vs Epoxy Flow Over Sides

Casting Resins are normally much thinner mixtures when compared to epoxy coating resins. That is because casing resins are usually slower to cure, thus produce less heat, which in turn, allows them to be poured thicker. However, this presents a problem when casting resins are used in coating applications. Because the mixture is thinner, it will often run off the edges of the project or require a dam/frame to be built to hold the material in. 

-Cure Times

Longer Cure Times

Casting resins cure much slower than epoxy resins. Casting resins typical cure in 36-48 hours and epoxy resins cure in 12-24 hours. However, epoxy resins will begin to gel in as quick as 20 minutes, whereas casting resins may take upwards of 18 hours to gel. Because casting resins are typically capable of thicker pours, they dissipate heat (exotherm) much slower than coating epoxy. If some coating epoxies are left in a mixing container beyond 5-10 minutes, they will react in an accelerated fashion producing excessive heat. Pouring a coating epoxy too thick (as in a river table) could ruin a project as the epoxy could heat up, and potentially crack. 

-Working Time

Working Time Of Epoxy

Not to be confused with cure time is working time. Sometimes called gel time or pot time, working time, as the name implies, is the amount of time before the material begins to gel/set up. Past this time, the mixed material cannot be moved easily or bubbles easily popped. Because casting resins cure much slower, they have much longer working times. Coating epoxies often have working times of 20 +/- 5 minutes. 20 minutes is often less time than many people need to properly prep/pour a project. This time can also be significantly reduced if pouring in hot environments or by leaving large amounts of epoxy in the mixing container too long before pouring. 

-Maximum Pour Depth

Thick Pour Vs Thin Pour

Many coating epoxies require thin pours of no more than 1/8-1/4 inch per application. If poured thicker than the recommended max pour depth, then an accelerated reaction could occur. Some casting resins, on the other hand, can be poured as thick as several inches per application. This property makes casting resins suitable for river tables, molds, figurines, and deep encapsulation projects. 

-Hardness

Faux Water Resin

Generally, (but not always) coating epoxy resins are harder than casting resins. Casting resins often have the ability to vary mix ratios which ultimately allow a variance in hardness. The best example of this is seen in casting resin used as faux water for a vase. If a casting resin is used with no flexibility, the vase will ultimately crack as the glass expands and contracts. Therefore, more flexible mixtures are necessary for these types of applications which can usually be accomplished by varying the amount of hardener (curing agent) used. However, each and every casting resin is different; research each as to the suitability for your individual project. Lastly, coating epoxies usually offer superior scratch resistance compared to casting resins. 

-Mix Ratios

Graduated Mixing Container For Epoxy

In a very broad generalization, most casting resins vary mixing ratios such as 2:1, 3:1 and even 1:1. A vast majority of available coating epoxies utilize a 1:1 by volume mixture. Many users find working with a 1:1 by volume the easiest. Varied ratios like 2:1 and 3:1 require graduated mixing containers to ensure accurately measured material. In either case, mixing rations MUST BE MEASURED ACCURATELY or the resin may not cure properly. 

-UV Resistance 

Yellowing Epoxy Comparison

Both casting resins and epoxy coating resins are capable of containing UV inhibitors. However, yellowing due to UV exposure can be more noticeable on thick, standalone casting projects. Because these projects are not backed by the color of wood grain, paint, stain etc, yellowing can be more noticeable. As with both, some epoxy resins resist yellowing better than others. Coating epoxies often better hide/distort yellowing when backed by the grain of wood or darker colored paints and stains on the substrate of the project. Most casting resins and coating epoxy systems are NOT RECOMMENDED for permanent outdoor use or direct exposure to UV. 

-Susceptibility To Bubbles

Both materials are equally susceptible to bubble formation on the substrate and encapsulated items. Bubbles may be less noticeable with casting resin as it is a thinner material which allows bubbles to rise to the surface and ultimately pop easier. However, with both materials bubbles can be drastically reduced by properly preparing a project. Porous surfaces, such as wood, should be initially coated with thin seal coat. A thin seal coat allows the epoxy to flow into (and seal) all porous areas and air to easily rise to the surface. Items which will be encapsulated, should also be sealed prior to being placed in a project. Items with many grooves, corners and open areas are prone to holding/trapping air in an epoxy project. 

-Heat Tolerance/Resistance

Most casting resins and epoxy resins which are meant for the average Do-It-Yourselfer are not high heat epoxies. High heat epoxy systems can be quite expensive. Generally, both casting resins and epoxy resins will begin to soften around 120-150°. This is especially important for those considering countertops, coasters, and other projects which may come in contact with hot pots, pans, coffee mugs and other hot items. 

An Exception To The Rules

It goes without saying that we have made some sweeping generalization in this comparison between epoxy and resin. However, there are so many different variations available to be able to simplify the differences we have to generalize the differences. The terms "usually", "generally", and "normally" are used liberally throughout this comparison. As with many things in life, there are exceptions to the rules. Casting resins can be used for coating applications, but may require additional steps such as a dam or frame prior to use. Alternatively, coating epoxies can be used for casting applications, but may need to be poured in multiple layers. Each project is unique and the suitability of materials should be considered before every project.